A Spec Auto Specialties & Customs

Performance services

Custom exhaust and TIG fabrication in Ocala, FL

We build exhaust systems from mandrel-bent tubing with tight joints and full-penetration TIG welds that seal and hold up to heat cycling.

The short answer

A Spec Auto Specialties & Customs fabricates mandrel-bent, TIG-welded exhaust systems and related custom metalwork at our Ocala, Florida shop, sized for the engine, the sound you want, and the ground clearance the chassis actually has. Joints are sealed so they hold up to heat.

A factory muffler replacement is a different job from a turbo downpipe, a custom X-pipe for an engine swap, or a full exhaust that clears a lowered chassis. At A Spec Auto Specialties & Customs we fabricate that kind of work in Ocala with mandrel-bent tubing so the pipe keeps its diameter through the bend. Joints are TIG-welded and checked, because a leak ahead of the oxygen sensor corrupts the air-fuel readings a tune depends on. We size tubing for the engine and any power adder, place resonators and mufflers for the sound you asked for, and hang the system so it is less likely to crack after track sessions at The FIRM or passes at Gainesville Raceway. Drivers from Marion County, The Villages, Belleview, and Gainesville bring this work to 422 SW 16th St when a catalog part will not fit or will not last.

Key facts

  • Methods: mandrel-bent tubing and TIG welding
  • Typical work: cat-back and full systems, headers and swap exhaust, turbo downpipes, V-band joints, sensor bungs
  • Materials often include stainless tubing, performance mufflers and resonators, and aftermarket headers or downpipes
  • Shop: 422 SW 16th St, Ocala, FL 34471

What exhaust and fabrication work do we build in Ocala?

Custom cat-back and full exhaust systems

We build systems from mandrel-bent stainless tubing, with diameter, X-pipe or H-pipe crossovers, resonators, and mufflers chosen for your power level and sound target.

Header installation and swap exhaust

We install headers and fabricate the connecting pipe for LS/LT, Coyote, HEMI, and other engine swaps, including fit-up around the steering, oil pan, and transmission crossmember.

Turbo downpipes and forced-induction exhaust

We build or fit downpipes and the rest of the exhaust so they complement Garrett, Whipple, or ProCharger systems and leave the oxygen sensors in the right place for a tune.

TIG fabrication and brackets

Custom mounts, V-band joints, and sensor bungs are part of the same fabrication work when a catalog part will not do.

How do we design and fabricate a custom exhaust?

  1. 01

    Design and mandrel-bent fit-up

    We pick tubing diameter and routing, then cut and tack the mandrel-bent sections on the car. Before final welding, we check chassis, suspension, driveline, and heat-sensitive clearance through travel.

  2. 02

    TIG welding and leak checks

    Joints are welded and inspected so the system seals, especially upstream of the oxygen sensors.

  3. 03

    Hang, shield, and road-ready check

    We hang the system, add heat protection where it is needed, and check for contact and leaks before the car leaves.

What materials and components do we work with?

  • American muscle
  • European and exotic
  • JDM and imports
  • Performance trucks

Materials and components we work with: mandrel-bent stainless steel tubing, V-band clamps and flanges, performance mufflers and resonators, aftermarket headers and downpipes, and O2 and EGT sensor bungs. We also fit exhaust components that complement forced-induction systems from Garrett, Whipple, and ProCharger.

American muscle

V8 cat-backs, headers, and swap exhausts, including LS/LT, Coyote, and HEMI combinations.

European and exotic

Custom systems for European performance platforms, built around the chassis and the intended use.

JDM and imports

Turbo-back and header-back work for import performance cars.

Performance trucks

Truck exhaust and fabrication, quoted after we see ride height, hitch use, and the engine combination.

Technician working under a vehicle on a lift

Custom Exhaust & Fabrication

Tell us what you drive, what is in the exhaust now, and how you want it to sound and perform. We will design and TIG-fabricate a mandrel-bent system that fits the car and seals. Call (352) 304-3237 or visit 422 SW 16th St, Ocala, FL 34471.

Frequently asked questions

Can you match a certain sound?

We can steer the sound with tubing size, crossovers, resonators, and mufflers, and we will be honest about what a given layout is likely to do. We will not promise a exact decibel number we have not measured on your car.

Do I need a tune after an exhaust change?

It depends on how much the airflow and the sensor locations change. A small cat-back on a lightly modified car may not need a new calibration. A downpipe, header, or swap exhaust often does. We will tell you what we recommend for the work you asked us to build.

Do you only work in stainless?

Mandrel-bent stainless is what we use most, because it holds up to heat and weather. Other materials are discussed if the job calls for them.

Updated

Get a quote

Request a custom build quote

Tell us what you drive, what is in the exhaust now, and how you want it to sound and perform. We will design and TIG-fabricate a mandrel-bent system that fits the car and seals. Call (352) 304-3237 or visit 422 SW 16th St, Ocala, FL 34471.

Need the car looked at? Call A Spec and we will talk through the next step.

Call (352) 304-3237, email info@ocalaautorepairshop.com, or request an appointment. The shop is open Monday–Friday, 9:00 AM to 5:00 PM.

Location of A Spec Auto Specialties & Customs

A Spec Auto Specialties & Customs

422 SW 16th St
Ocala, FL 34471
(352) 304-3237

Monday–Friday, 9:00 AM to 5:00 PM. Closed Saturday and Sunday.

Call (352) 304-3237Book service